Febris TH and NFC and Downlink Description

Are you looking for the Febris TH and NFC and downlink description?

Here you will find the NFC and downlink description for the Febris TH

Febris TH NFC and downlink table

Here you will find the table for a clear visualisation:

🔽🔽

Timings & Alarms group

Name: Measuring period
Communication protocol: All
Description: Specifies the period in which the measured values are recorded. 10 minutes means that a measurement is always taken by the sensor after 10 minutes.
Key (NFC parameter): period
Module: Sentiface
Module key: 0x1111
Group: 0x00
Property ID: 0x00
Preset value: 5
Minimum adjustable value: 5
Maximum adjustable value: 60
Unit: min
read/write: rw
Module key: 1111

Name: Regular transmission interval
Communication protocol: All
Description: Number of measurements after the sensor still schedules an uplink despite the absence of an alarm condition.
Module: Sentiface
Module key: 0x1111
Group: 0x00
Property ID: 0x01
Preset value: 6
Minimum adjustable value: 1
Maximum adjustable value: 12
Unit: Anzahl
read/write: rw
Module key: 1111

Name: Save and transfer values (Use feature only after consultation)
Communication protocol: All
Description: Specifies whether past measured values are also sent: (from Minor version 1.2)

0: off
1: on

Module: Sentiface

Module key: 0x1121
Group: 0x00
Property ID: 0x02
Preset value: Use feature only after consultation
Minimum adjustable value: Use feature only after consultation
Maximum adjustable value: Use feature only after consultation
Unit:
read/write: rw
Module key: 1121

Name: Number of stored values (Use feature only after consultation)
Communication protocol: All
Description: Maximum number of past measured values that are sent with a transmission. The actual number depends on the technology (from Minor version 1.2)
Key (NFC parameter): pastnum
Module: Sentiface
Module key: 0x1121
Group: 0x00
Property ID: 0x02
Preset value: Use feature only after consultation
Minimum adjustable value: Use feature only after consultation
Maximum adjustable value: Use feature only after consultation
Unit:
read/write: rw
Module key: 1121

Alarm Settings group

Name: Delta value
Communication protocol: All
Description: Specifies the absolute amount by which the CO2 value must change compared to the last transmission for an ALARM transmission to be triggered. This transmission is carried out independently of the normal transmission interval.
Key (NFC parameter): delta
Module: Sentiface
Module key: 0x1111
Group: 0x01
Property ID: 0x00
Preset value: 300
Minimum adjustable value: 100
Maximum adjustable value: 2000
Unit: ppm
read/write: rw
Module key: 1111

Name: Threshold value for yellow alarm
Communication protocol: All
Description: Specifies the CO2 threshold in ppm that must be exceeded for the sensor to switch to the yellow state (yellow LED lights up).
Key (NFC parameter): yellow
Module: Sentiface
Module key: 0x1111
Group: 0x01
Property ID: 0x01
Preset value: 1000
Minimum adjustable value: 500
Maximum adjustable value: 3000
Unit: ppm
read/write: rw
Module key: 1111

Name: Threshold value for red alarm
Communication protocol: All
Description: Specifies the CO2 threshold in ppm that must be exceeded for the sensor to switch to the red state (red LED lights up).
Key (NFC parameter): red
Module: Sentiface
Module key: 0x1111
Group: 0x01
Property ID: 0x02
Preset value: 2000
Minimum adjustable value: 500
Maximum adjustable value: 3000
Unit: ppm
read/write: rw
Module key: 1111

Name: Hysterese
Communication protocol: All
Description: Determines the absolute hysteresis in ppm for state changes. If the CO2 concentration falls below a threshold value minus hysteresis, the system switches from a higher to a lower alarm status.
Key (NFC parameter): hyst
Module: Sentiface
Module key: 0x1111
Group: 0x01
Property ID: 0x03
Preset value: 100
Minimum adjustable value: 0
Maximum adjustable value: 300
Unit: ppm
read/write: rw
Module key: 1111

Alarm data source and humidity alarm group

Name: Alarm data source
Communication protocol: All
Description: Source on which the alarm is triggered, e.g. CO2, temperature or relative humidity

0: CO2 Sensor
1: Rel. humidity sensor

Key (NFC parameter): ads
Module: Sentiface
Group: 0x05
Property ID: 0x00
Preset value: 1
Minimum adjustable value: 0
Maximum adjustable value: 1
Unit:
read/write: rw
Module key: 1111

Name: Rel. humidity Delta
Communication protocol: All
Description: Specifies by how much the relative humidity value must change in absolute terms compared to the last transmission for an ALARM transmission to be triggered. This transmission
is carried out independently of the normal transmission interval.
Key (NFC parameter): hdt
Module: Sentiface
Group: 0x05
Property ID: 0x01
Preset value: 20
Minimum adjustable value: 5
Maximum adjustable value: 100
Unit: %
read/write: rw
Module key: 1111

Name: Rel. humidity yellow alarm
Communication protocol: All
Description: Specifies the relative humidity threshold in ppm that must be exceeded for the sensor to switch to the yellow state (yellow LED lights up).
Key (NFC parameter): hyt
Module: Sentiface
Group: 0x05
Property ID: 0x02
Preset value: 60
Minimum adjustable value: 10
Maximum adjustable value: 100
Unit: %
read/write: rw

Module key: 1111

Name: Rel. humidity red alarm
Communication protocol: All
Description: Specifies the relative humidity threshold in ppm that must be exceeded for the sensor to switch to the red state (red LED lights up).
Key (NFC parameter): hrt
Module: Sentiface
Group: 0x05
Property ID: 0x03
Preset value: 80
Minimum adjustable value: 10
Maximum adjustable value: 100
Unit: %
read/write: rw
Module key: 1111

Name: Rel. humidity Hysterese
Communication protocol: All
Description: Determines the absolute hysteresis in ppm for state changes. If the CO2 concentration falls below a threshold value minus hysteresis, the system switches from a higher to a lower alarm status.
Key (NFC parameter): hlh
Module: Sentiface
Group: 0x05
Property ID: 0x04
Preset value: 5
Minimum adjustable value: 0
Maximum adjustable value: 300
Unit: %
read/write: rw
Module key: 1111

Documentation Links

You can find the links for further documentation on Febris TH here: