Skip to content
English
go to www.sentinum.de
  • There are no suggestions because the search field is empty.

Juno Tracker LoRaWAN NFC and Downlink description

Need clear information on Juno Tracker LoRaWAN NFC and downlink parameters?

SENTIFACE – LoRaWAN NFC & Downlink Configuration
📄 You can view the document above or download the PDF here .
Contents

1. Version history

Version Date Revision
1.0.018.02.2025Creation
1.0.124.04.2026Formatting, version history

2. Module overview

Module Module key Group Group ID Description
Sentiface 0x1XXX Timings 0x00 Defines parameters for measurements and transmission behavior
Sentiface 0x1XXX Alarms and limit values 0x01 Defines alarms and limit values such as upper and lower temperature limits
Sentiface 0x1XXX Tracking on Activity 0x04 Defines thresholds and settings for the Tracking on Activity feature

Tables for cross‑product modules (Senticom/Sentivisor) can be found in the Generic NFC and Downlink documentation .

Further information on configuring sensor communication and tracking settings can be found in the respective generic LoRaWAN® or mioty® documentation, depending on the version.

3. Instructions valid for versions

Article codeFeatures
S-JUNO-LOEU-TH-TRACKJUNO TH Tracker with temperature and relative humidity, tracking function and Tracking on Activity LoRaWAN®
S-JUNO-IX-LOEU-TH-TRACKINDUSTRIAL JUNO TH Tracker with temperature and relative humidity, tracking function and Tracking on Activity LoRaWAN®
S-JUNO-LOEU-TRACKJUNO Tracker with Tracking on Activity LoRaWAN®
S-JUNO-IX-LOEU-TRACKINDUSTRIAL JUNO Tracker with Tracking on Activity LoRaWAN®

4. Sentiface – Group Timings (0x00)

ResourceIDDescriptionKey MinMaxFactory settingUnitModule key
Measurement period 0x00 Specifies the period in which the measured values are recorded. 5 minutes means that a measurement is always taken by the sensor after 5 minutes. period 1 / 5* 360 30 min 1111
Regular transmission interval 0x01 Number of measurements performed before transmission. every 1 64 6 1111

*
5: For version S-JUNO-LOEU-TH and S-JUNO-MIOTY-TH
1: For version S-JUNO-IX-LOEU-TH and S-JUNO-IX-MIOTY-TH

5. Sentiface – Group Alarm Settings (0x01)

Resource Resource ID Description Key
(NFC/BLE)		 Min Max Factory setting Unit Module key
Alarm active 0x00 Indicates which alarms are activated, whether for temperature or relative humidity:
  • 0: Both alarms deactivated
  • 1: Temperature alarm active
  • 2: Relative humidity alarm active
  • 3: Both alarms active
 alarm_act 0 3 1 1111
Temperature delta 0x01 Specifies by how much the temperature must change in absolute terms compared to the last transmission for an alarm transmission to be triggered. This transmission is carried out independently of the normal transmission interval. tdt 1 50 5 °C 1111
Temperature upper limit 0x02 Specifies the upper absolute limit value at which an alarm is triggered. tht 0 85 40 °C 1111
Temperature lower limit 0x03 Specifies the lower absolute limit value at which an alarm is triggered. tlt -25 75 0 °C 1111
Relative humidity delta 0x04 Specifies by how much the relative humidity must change in absolute terms compared to the last transmission for an alarm transmission to be triggered. This transmission is carried out independently of the normal transmission interval. hdt 1 80 20 %RH 1111
Relative humidity upper limit value 0x05 Specifies the upper absolute limit value of the relative humidity at which an alarm is triggered. hht 5 100 80 %RH 1111
Relative humidity lower limit value 0x06 Specifies the lower absolute limit value of the relative humidity at which an alarm is triggered. hlt 0 95 20 %RH 1111
Hysteresis temperature 0x07 Determines the absolute hysteresis in degrees Celsius for state changes. If the temperature falls below or exceeds a threshold value minus hysteresis, the system switches from a higher to a lower alarm state. thy 0 30 5 °C 1111
Hysteresis relative humidity 0x08 Determines the absolute hysteresis in percent relative humidity for state changes. If the relative humidity falls below or exceeds a threshold value minus hysteresis, the system switches from a higher to a lower alarm state. hhy 0 10 2 %RH 1111

6. Sentiface – Group Tracking on Activity Settings (0x04)

Resource Resource ID Description Key
(NFC/BLE)		 Min Max Factory setting Unit Module key
Move mode 0x00 Indicates whether Tracking on Activity mode is activated:
  • 0: No Tracking on Activity feature active
  • 1: Tracking on Start – localization is carried out when an activity is detected
  • 2: Tracking on Ongoing – localization is carried out during an ongoing activity
  • 3: Tracking on Start and Ongoing – localization is carried out when an activity is detected and while an activity is already running
  • 4: Tracking on Inactivity – localization is carried out when an activity is finished
  • 5: Tracking on Start and Inactivity – localization is carried out when an activity is detected and when the activity ends
  • 6: Tracking on Inactivity and Ongoing – localization takes place while the activity is in progress and after it has ended
  • 7: Tracking on Start, Inactivity and Ongoing – localization takes place when the activity starts, while it is in progress and when the activity has ended
lmode 0 7 6 1111
Move activity threshold 0x01 Describes the acceleration from which a movement is counted and recorded as an activity. moat 100 2000 400 mg 1111
Move ongoing time 0x02 Specifies the time that elapses between two transmissions and localizations while an activity is ongoing. mont 1 1440 10 min 1111
Move inactivity time 0x03 Describes the time between the point at which an activity ends and the localization or transmission of the data. moit 1 1440 5 min 1111


Unterstützte Funktechnologien CE Kennzeichnung und Entsorgungssymbole

© Sentinum GmbH – All rights reserved.

All contents of this document, including text, tables and images, are protected by copyright and are the property of Sentinum GmbH.

All images are subject to the copyright of Sentinum GmbH unless otherwise stated.

Reproduction, distribution or use — even in part — is not permitted without explicit written authorization.

Specifications are subject to change. All information is provided without guarantee.