NYX – NFC & Downlink Description

📄 You can view the PDF above or download it here .

Version	Date	Revision
1.0.0	18.02.2025	Creation
1.0.1	24.04.2026	Formatting, version history

Module	Module Key	Group	Group ID	Description
Sentiface	`0x1XXX`	Timings	`0x00`	Defines parameters for measurements and transmission behavior
Sentiface	`0x1XXX`	Settings for opening detection	`0x02`	Defines measurement thresholds for triggering the alarm for temperature and relative humidity
Sentiface	`0x1XXX`	Settings for tilt detection	`0x03`	Defines the behavior of the acceleration sensor

Tables for cross-product modules (Senticom / Sentivisor) can be found in the Generic NFC and Downlink documentation .

Further information on configuring sensor communication can be found in the respective generic LoRaWAN® documentation or mioty® documentation , depending on the version.

Article Code	Features
S-JUNO-LOEU-ID	JUNO tilt sensor, tilt detection and opening detection LoRaWAN®
S-JUNO-IX-LOEU-ID	INDUSTRIAL JUNO tilt sensor, tilt detection and opening detection LoRaWAN®
S-JUNO-MIOTY-ID	JUNO tilt sensor, tilt detection and opening detection mioty®
S-JUNO-IX-MIOTY-ID	INDUSTRIAL JUNO tilt sensor, tilt detection and opening detection mioty®

Instructions valid for versions listed above.

Resources	Resource ID	Description	Key (NFC/BLE)	Min	Max	Factory Setting	Unit	Module Key
MEASUREMENT PERIOD	`0x00`	Specifies the period in which the measured values are recorded. 5 minutes means that a measurement is always taken by the sensor after 5 minutes.	`period`	1 / 5*	360	30	min	`1111`
REGULAR TRANSMISSION INTERVAL	`0x01`	Number of measurements performed up to transmission.	`every`	1	64	6		`1111`

*
5: For version S-JUNO-LOEU-ID and S-JUNO-MIOTY-ID
1: For version S-JUNO-IX-LOEU-ID and S-JUNO-IX-MIOTY-ID

Property	Property ID	Description	Key (NFC/BLE)	Max	Default	Unit	Module Key
OPENING COOLDOWN	`0x00`	Specifies a period of time in which, after the triggering of an opening, further opening cannot be triggered (debounces the openings). The reference value is the last counted opening.	`acool`	600	0	sec	`1111`
OPENING TIME ALARM	`0x01`	Indicates how long the lid is open until an alarm is triggered.	`oaaf`	2880	0	sec	`1111`
OPENING MODE	`0x02`	Describes which direction the sensor is facing when it is closed and which angles are defined for opening detection. Face up describes the status when the sensor is lying on the table and looking up at the ceiling. Settings 0–7 use the acceleration sensor, 8–9 use the Hall sensor: `0`: Off `1`: Ultra low power. Fixed threshold 50°. Closed when directed downwards (face down). `2`: Ultra low power. Fixed threshold 50°. Closed when directed upwards (face up). `3`: Ultra low power. Fixed threshold 50°. Closed when directed sideways. `4`: Extended tilt sensing. Adjustable threshold. Closed when directed downwards. `5`: Extended tilt sensing. Adjustable threshold. Closed when directed upwards. `6`: Extended tilt sensing. Adjustable threshold. Closed when directed sideways. `7`: Extended tilt sampling. Adjustable threshold. Automatic calibration of the closed alignment. `8`: Container is closed when solenoid is applied. `9`: Container is open when solenoid is applied.	`opmo`	8	1		`1111`

Property	Property ID	Description	Key (NFC/BLE)	Min	Max	Default	Unit	Module Key
SAMPLING PERIOD	`0x00`	Specifies how often the acceleration sensor determines the angle. The higher the frequency, the higher the power consumption.	`tspe`	2	600	2	s	`1111`
TRIGGER LEVEL	`0x01`	Specifies the angle from which an opening is counted or an alarm is triggered.	`ttle`	5	180	20	°	`1111`
TRIGGER HYSTERIA	`0x02`	Hysteresis value for the opening angle.	`tthy`	1	90	4	°	`1111`

Juno ID TILT NFC and Downlink description

Are you looking for the Juno ID TILT NFC and downlink description?